Used Arctic Cat Snowmobile Parts
First buyer to complete payment on part gets it.
|
Top End |
||||
| 530 Twin | Cylinder | Cylinder core, needs replated. Stock porting. Can re-nikasil for an additional cost. |
$75 |
|
| 600 EFI Twin Non-APV | Cylinders | Cylinder cores, need replated. Stock porting. Can re-nikasil them for an additional cost. |
$75 |
|
| 600 Twin APV | Cylinder | Cylinder core, needs replated and welded. Stock porting. Can re-nikasil them for an additional cost. |
$55 |
|
| 600 EFI Twin Non-APV | Head | Slight pitting in one dome, otherwise in good shape. Includes temp sensor. | $60 |
|
| M7 - F7 | Head | Head is in good condition. | $60 |
|
| 900 Thundercat Triple | Cylinders | Cylinder cores, need replated. Stock porting. Can re-nikasil them for an additional cost. |
$75 |
|
| 900 Thundercat Triple | Top End | Cylinders, heads and pistons. Excelent shape. | $625 |
|
| M1000 | Power Valves | New Power Valve Assy, PTO and Mag |
$175 |
|
|
Bottom End |
||||
| 600 EFI | Crankcase Halves | Case is in good shape, out of a 1998 ZR 600 EFI |
$150 |
|
| 900 Twin | Crankcase Halves | Clutch balance ring came loose and broke tore the case up. Case still seals tight and holds air. Could be welded for strength. Pic of damage |
$75 |
|
| 900 Twin EFI | Crankshaft | Crank has 450 miles on it and is in good condition. Fits EFI flywheels only. |
$250 |
|
| Thundercat 900 | Crankshaft | Fresh rebuild 900 triple crank. Never installed or fired, still in plastic bag. |
$725 |
|
| M1000 | Crankcase Halves | Bearing pin pressed into case due to misaligned bearing. Needs new pin hole drilled. Case is clean otherwise. Pic of pressed pin |
$125 |
|
| M1000 | Crankcase Halves |
Motor lost a rod bearing and the rod gauled the case. Case needs to be weled or sealed up on the backside of the gauling, has 1/4" hairline crack. Otherwise case is in good usuable shape. |
$125 |
|
| Thundercat 1000 | Crankcase Halves | Case is in good shape. A couple of dings in side from injesting something, but very usable. |
$350 |
|
|
Electrical |
||||
| ZR 600 | Flywheel | 1998 ZR 600 EFI flywheel | $100 |
"No Photo" |
| ZRT 600 | Ignition | ZRT 600 CDI, Stator and Flywheel out of 1998 ZRT 600 | $225 |
|
| ZR 700 | CDI | 1999 ZR/Powder Special 700 3D CDI | $100 |
"No Photo" |
|
Thundercat |
CDI | 2000 Thundercat 1000 3D CDI | $100 |
|
| M8 - M1000 | Magneto | Stator and Flywheel | $400 |
|
|
M8 - M1000 and others |
Coils |
Brand new, never used |
$40 |
|
| All Sleds | Analog Speedometer | Analog speedo with 482 miles. | $40 |
|
|
Carburetors and Throttle Bodies |
||||
| Mikuni VM36 | 3 Carbs | VM36 Round Slide Carbs with magnetic safety switch. Set of 3. | $100 |
|
| Mikuni VM38 | 3 Carbs | VM38 Round Slide Carbes bored out to 39.5mm. Carbs are in excellent shape, | $250 |
.JPG)
|
| Mikuni VM40 | 1 Carb | VM40 round slide carb with magenetic safety switch. Needs rebuilt and missing some parts. Body is in good shape. Will completely rebuild for an additional $75. | $50 |
|
| 600 Twin EFI Non-APV | Throttle Body Assy | Great shape, fits 98-2000 600 Twin EFI with "Square" ECU | $200 |
|
|
Clutches/Drivetrain |
||||
| M-Series | Diamond Drive | Diamond Drive with reverse. 57/63 gearset. Catmaster Tech inspected and new update seal installed. Approx 900 miles. Fits 07-08 M6 and M8 | $500 |
.JPG)
|
| 33 MM Cranks | Primary Clutch | Used 6 tower clutch, set-screw weights and a new spider. Fits most newer sleds. | $175 |
|
|
Misc |
||||
| M8 - M1000 | Recoils | Large diameter rewind, great shape |
$75 |
|
| King Cat | Rear Scissor |
Mountain Magic rear scissor arm. Improves trail handing and powder performance. Brand new. Pictured next to stock. |
Sold |
|
| Skis | Plastic Skis | USI Project X Skis, brand new. Need mount kit and carbides. | $125 |
|
| Short Track Sleds | 121" Skid | 121" Skid out of a 2001 ZR. Has clicker ACT shocks. | $400 |
|